Uniden EXR2460 Owner's Manual

3) Rotate the mounting adapter180° and snap it into placeat the bottom of the base.4) Plug the AC adapter cord into the 10 V DC input jack on the back

7) Line up the mounting slots on the basewith the mounting screws on the wall,then push in and down until thephone is firmly seated.8) On the base uni

INSTALLING THE HANDSET BATTERY PACK1) Press in on the battery cover releaseand slide the cover down until itcomes off.2) Install the nickel-cadmium ba

CHARGING THE BATTERY PACK▼Initial battery chargingBefore plugging the phone line into your new phone for the first time,fully charge the battery pack

▼Low battery indicatorWhen the battery pack is very low andneeds to be charged, the phone isprogrammed to eliminate functions inorder to save power. I

ADJUSTING THE HANDSET VOLUME CONTROLS▼Handset ringer volumeWhen the phone is in standby mode, pressing thevol▲ or ▼ key onthe handset selects the hand

INSTALLING THE BELTCLIP▼To attach the beltclip1) Remove the slot cover.2) Insert the beltclip into the empty slotand press down until it clicks.▼To re

HEADSET INSTALLATIONYour phone may be used with an optional headset,the Uniden HS910. To use this feature, simplyinsert the headset plug into the head

Using YourNew PhoneMAKING AND RECEIVING CALLSHandset On Base Handset Off BaseTo answera call1) Pick up the handset.2) If not in Autotalk Mode,presstal

STORING A PHONE NUMBER IN MEMORY1) Remove the handset from the base.2) Press and holdmemoryuntil theconfirmation tone sounds. The followingscreen appe

CONTENTSOF YOUR OWNER’S MANUALCONTENTSIntroduction...1•Welcome...

EDITING A PHONE NUMBER IN MEMORYFollow these steps to edit a phone number that you have alreadyprogrammed into memory.1) Remove the handset from the b

9) Pressselect.The handset beeps anddisplays a confirmation screen. Forexample, if you store a name and numberinto memory location number one, thenthe

8) Pressselect. There is a confirmationtone, and the handset displaysMemory 1 Deleted.9) The display then returns to the Memory Store screen. You may

USING CALLER IDYou must subscribe to Caller ID from your phone company inorder to use this feature.▼Setting up Caller ID optionsThere are three Caller

▼Screening your callsCaller ID allows you to review callerinformation before you answer yourphone. After the first ring, the displayshows the date, ti

▼Calling a Caller ID number1) Presscall id, and the Caller ID summaryscreen appears. The screen shows thenumber of new messages andtotal messages.2) S

▼Deleting a Caller ID messageTo delete a single Caller ID message, follow the steps below.1) Presscall id, and the Caller ID summaryscreen appears. Th

4) A confirmation tone sounds, and thefollowing screen appears.5) Presscall idto return to standby.USING REDIALTheredialkey redials the last numberdia

USING THE PAGE FEATURETo locate the handset (while it’soff the base), presspageonthe base.To beep the handset for 5seconds, presspageon the base,and t

TroubleshootingQUICK REFERENCE CHARTIf your phone is not performing to your expectations, please try thesesimple steps before calling Uniden customer

oductionWELCOMECongratulations on your purchase of the Uniden EXR2460 cordlesstelephone. This phone is designed for reliability, long life, andoutstan

PROBLEM SUGGESTIONThe handset doesn’t ring orreceive a page.•The Nickel-Cadmium battery packmay be weak. Charge the batteryon the base unit for 12-15

SpecificationsGENERALThe EXR2460 complies with FCC Parts 15 and 68.Frequency control: PLLModulation: Direct Sequence Spread Spectrum; DBPSKOperating t

AND FUNCTIONSCONTROLS

June19994,511,7614,523,058 4,595,795 4,797,916 5,381,460 5,426,6905,434,9055,491,745 5,533,010 5,574,727 5,650,790 5,660,2695,661,7805,663,

INCLUDED IN YOUR PACKAGE•This Owner’s Manual•Precautions and Important Safety Instructions•Registration Card2Wall MountingScrewsTIPTo get the most fro

Installing and Adjusting YourPhoneDESK/TABLETOP INSTALLATION1) Plug the AC adapter cord into the 10 V DC input jack on the back ofthe base.2) Wrap the

7) Attach the desktop stand to the base.8) Set the base on a desk or tabletop andplace the handset into the base. Then,raise the antenna to a vertical

3) Plug the AC adapter cord into the 10 V DC input jack on the back ofthe base.4) Put the AC adapter cord inside themolded wiring channel, then wrap i

7) On the base unit, pull the handsetretainer out of the slot and rotateit clockwise 180°.8) Flip the retainer from front to back,then slide it back i

▼Direct wall mountingIf you don't have a standard wall plate, you can mount your phonedirectly to the wall. Before doing this, consider the follo