Uniden UBCD996T Owner's Manual Page 114
- Page / 148
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
114
Fire Tone-Out
Your scanner can be set to respond to fire tone-outs, a system comprised of
standardized two-tone sequential paging, short one-tone paging, and long group
tone paging. You can save up to 10 settings. When you select a setting in standby
mode, the scanner also monitors for any other setting that uses the same transmit
frequency, modulation, and attenuation settings. To quickly switch to Fire Tone-Out
mode, press and then .
You need tone-out setup information from the agency you wish to monitor. Check
with your local agency or on-line resources.
The Fire Tone-Out feature is not used in Australia or New Zealand.
Turn the to select which of the ten tone-outs to monitor. Or, while
holding on any channel, press then to quickly switch to Tone-Out Standby,
then rotate scroll to select the settings to monitor. All tone-outs that have the same
frequency, modulation, and attenuation setting as the one you select, are also
monitored.
In standby mode, the display cycles through all monitored tone-out settings.
Regardless of the current display, the scanner always alerts on any received tone-
out that matches a stored setting.
If you press while in standby mode, the scanner temporarily exits
the mode and you hear all transmissions on that frequency. No alerts sound, even if
a tone-out matches one you have stored. Press again to return to
standby mode.
Scroll to select the tone-out (1 - 10) you want to program, then press . Then you
can scroll to any of the following settings and press to select and modify the
selected settings:
— Sets the name for the selected tone-out setting.
Sets the tone-out’s RF frequency parameters. Then select:
[SQ]
Note:
[MENU]
Scroll Control
[SQ]
[HOLD/RESUME]
[HOLD/RESUME]
[MENU]
—
Setting Tone-Out Standby
Setting Up Tone-Out
gQ g
g
Q
gQ g
g
Q
Q
Tone-Out for...
Tone-Out Standby
Tone-Out for...
Tone-Out Setup
Edit Name
Set Frequency
- OWNER'S MANUAL 1
- Precautions 2
- Power Related Issues 3
- Table of Contents 4
- Introduction 11
- Feature Highlights 12
- Auto Store 15
- Priority 15
- PC Control and Cloning 15
- Memory Storage Limits 16
- Search Lockout Limits 17
- About This Manual 17
- Understanding Quick Keys 21
- What is Scanning? 22
- What is Searching? 22
- What is CTCSS/DCS? 22
- Conventional Scanning 23
- Simplex Operation 23
- Repeater Operation 24
- What is Trunk Tracking? 24
- Trunked Scanning 25
- Types of Trunking Systems 25
- EDACS Trunking 26
- LTR Trunking 27
- Startup Configuration 28
- Multi-Site Trunking 28
- I-Call (Motorola/EDACS) 29
- Where To Get More Information 29
- UBCD996T 30
- Setting Up Your Scanner 31
- MOUNTING WOOD SCREWS 32
- Recording 33
- Vehicle Installation 33
- Mounting Using ISO Technique 36
- Removing the Display Sticker 37
- Controls, Keys, and Functions 39
- A Look At The Display 44
- Operation 45
- Scanning Systems 46
- Selecting Systems to Scan 47
- Locking/Unlocking Systems 48
- Locking/Unlocking Channels 48
- ID Scan/ID Search Mode 48
- Holding On a System 49
- Holding On a Channel 49
- Trunking Activity Indicators 50
- Toggling the Display Mode 51
- Optimizing P25 Performance 52
- Using the Menu 54
- Programming General Settings 55
- Adjusting the Key Beep 56
- Setting the Audio AGC 56
- Setting the GPS Format 57
- Setting the Serial Port Speed 58
- Viewing Memory Used 59
- Wired Cloning 60
- Programming Your Scanner 62
- Programming System Settings 67
- Setting ID Scan/ID Search MEL 70
- Setting Data Skip C 70
- Setting the Status Bit M 72
- Setting End Code Operation M 72
- Setting I-Call Operation ME 72
- Setting the EDACS ID Format E 73
- Editing Sites MESL 75
- Editing Channel Groups MECL 75
- Programming Sites MESL 76
- Setting Site Modulation ML 79
- Setting Site Attenuation MESL 79
- Setting Site Lockout MESL 79
- Setting Site Hold Time MESL 80
- Adjust P25 Level MEL 82
- Deleting Sites ME 83
- Programming Channels MECL 85
- Q Select the channel 86
- Set Record MECL 90
- Setting Lockout MESL 91
- Copying a Channel MESL 91
- Deleting a Channel MESL 91
- Searching and Storing 92
- Quick Search 93
- Custom Search 93
- Editing a Custom Search Range 94
- Search With Scan 95
- Set Delay Time 96
- Set Attenuator 97
- Set Record 97
- Auto Search and Store 98
- Trunked Search and Store 99
- Using the Close Call Feature 100
- Close Call Hits 102
- Close Call Hits with Scan 102
- Search and Close Call Options 104
- Priority Scan 110
- Fire Tone-Out 114
- Location-Based (GPS) Scanning 117
- Setting the Options 120
- Deleting a Location 121
- GPS Display Mode 122
- GPS Review Location Mode 123
- Care and Maintenance 125
- Troubleshooting 126
- Specifications 129
- Reference 132
- User Defined Fleet Maps 134
- Size Code Restrictions 135
- Quick Key 141
- Printed in China 148
- UBZZ01335AA(0) 148
Related products and manuals for Car media receivers Uniden UBCD996T
(64 pages)© 2020, manymanuals.com. All rights reserved. | 3.660 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals