Uniden UBCD996T Owner's Manual Page 14
- Page / 148
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Memory Backup
Temporary Lockout
Startup Configuration
Single-Handed Function Control Operation
Record Out Jack
Display and Keypad Backlight
Vehicle Power Connection (Orange Wire)
Trunk Tracker IV™ Operation
Multi-Site Trunking
Control Channel Only Scanning
Adaptive Digital Threshold
Location Based Scanning
GPS Non-Radio Based Features
GPS Display Mode
— If power is lost or disconnected, the scanner retains the
frequencies you programmed in its memory.
— Makes it easy to temporarily lock out a system, channel, or
frequency. The lockout is cleared when you turn power off, then back on so you
don’t have to remember to unlock the channels later.
— Lets you easily manage multiple configurations for your
scanner.
— You can tap the Function/Scroll
Control to enable the Function mode. It reverts to normal mode in about 3 seconds
from your last press if no other action occurs.
— Using the appropriate cable and audio recording device with
signal control, you can record live audio of designated channels.
— Makes the display and keypad easy to see in
dim light using two color options and six light levels plus off.
— Lets you connect to your vehicle’s
dimmer circuit to also dim the scanner’s display with the vehicle’s dimmer control.
— Follows unencrypted conversations on analog
Motorola, Motorola Astro 25 (APCO 25), EDACS, EDACS SCAT, and LTR trunked
radio systems, including systems in VHF, UHF, 700 MHz, 800 MHz, and 900 MHz
bands. The scanner can scan both conventional and trunked systems at the same
time.
— Lets you share system channels across multiple sites to
more efficiently use the scanner’s memory and more easily select sites to monitor.
— If the scanner is set to scan a Motorola
system, you can set it so it scans using only control channel data. You do not have
to program voice channel frequencies into memory in this mode as long as all
possible control channels are programmed.
— Automatically sets the digital decode threshold for
APCO 25 systems.
— If you connect a GPS unit to the scanner it can
automatically enable and disable systems based on the Location Information
(longitude, latitude, Range) that you provide.
— The scanner alerts you to Dangerous
Intersections, Speed Alerts, and Points of Interest that you program into the scanner.
— Lets you display extended GPS information such as
GPS
14
- OWNER'S MANUAL 1
- Precautions 2
- Power Related Issues 3
- Table of Contents 4
- Introduction 11
- Feature Highlights 12
- Auto Store 15
- Priority 15
- PC Control and Cloning 15
- Memory Storage Limits 16
- Search Lockout Limits 17
- About This Manual 17
- Understanding Quick Keys 21
- What is Scanning? 22
- What is Searching? 22
- What is CTCSS/DCS? 22
- Conventional Scanning 23
- Simplex Operation 23
- Repeater Operation 24
- What is Trunk Tracking? 24
- Trunked Scanning 25
- Types of Trunking Systems 25
- EDACS Trunking 26
- LTR Trunking 27
- Startup Configuration 28
- Multi-Site Trunking 28
- I-Call (Motorola/EDACS) 29
- Where To Get More Information 29
- UBCD996T 30
- Setting Up Your Scanner 31
- MOUNTING WOOD SCREWS 32
- Recording 33
- Vehicle Installation 33
- Mounting Using ISO Technique 36
- Removing the Display Sticker 37
- Controls, Keys, and Functions 39
- A Look At The Display 44
- Operation 45
- Scanning Systems 46
- Selecting Systems to Scan 47
- Locking/Unlocking Systems 48
- Locking/Unlocking Channels 48
- ID Scan/ID Search Mode 48
- Holding On a System 49
- Holding On a Channel 49
- Trunking Activity Indicators 50
- Toggling the Display Mode 51
- Optimizing P25 Performance 52
- Using the Menu 54
- Programming General Settings 55
- Adjusting the Key Beep 56
- Setting the Audio AGC 56
- Setting the GPS Format 57
- Setting the Serial Port Speed 58
- Viewing Memory Used 59
- Wired Cloning 60
- Programming Your Scanner 62
- Programming System Settings 67
- Setting ID Scan/ID Search MEL 70
- Setting Data Skip C 70
- Setting the Status Bit M 72
- Setting End Code Operation M 72
- Setting I-Call Operation ME 72
- Setting the EDACS ID Format E 73
- Editing Sites MESL 75
- Editing Channel Groups MECL 75
- Programming Sites MESL 76
- Setting Site Modulation ML 79
- Setting Site Attenuation MESL 79
- Setting Site Lockout MESL 79
- Setting Site Hold Time MESL 80
- Adjust P25 Level MEL 82
- Deleting Sites ME 83
- Programming Channels MECL 85
- Q Select the channel 86
- Set Record MECL 90
- Setting Lockout MESL 91
- Copying a Channel MESL 91
- Deleting a Channel MESL 91
- Searching and Storing 92
- Quick Search 93
- Custom Search 93
- Editing a Custom Search Range 94
- Search With Scan 95
- Set Delay Time 96
- Set Attenuator 97
- Set Record 97
- Auto Search and Store 98
- Trunked Search and Store 99
- Using the Close Call Feature 100
- Close Call Hits 102
- Close Call Hits with Scan 102
- Search and Close Call Options 104
- Priority Scan 110
- Fire Tone-Out 114
- Location-Based (GPS) Scanning 117
- Setting the Options 120
- Deleting a Location 121
- GPS Display Mode 122
- GPS Review Location Mode 123
- Care and Maintenance 125
- Troubleshooting 126
- Specifications 129
- Reference 132
- User Defined Fleet Maps 134
- Size Code Restrictions 135
- Quick Key 141
- Printed in China 148
- UBZZ01335AA(0) 148
Related products and manuals for Car media receivers Uniden UBCD996T
(64 pages)© 2020, manymanuals.com. All rights reserved. | 2.492 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals